!!

Welcome to our Forum, extension and content sharing platform of Electrical Test and Measurement Product Reviews Blog.

 
Registration this is Free, we accept contributors of 17 years old and above. We do not accept registration with Gmail

Active since 7 June 2012  


Copyright Notice: Entire ITTSB.EU content & images they are copyright protected. - Forum search engine disabled to Guests - No need of you using Adblock software.

Author Topic: BOSCH Ni-Cd 12V How should the battery terminals be connected?  (Read 9474 times)

0 Members and 1 Guest are viewing this topic.

Online Kiriakos GR

  • Administrator
  • Hero Member
  • *****
  • Join Date: May 2012
  • Location: Greece
  • Posts: 2203
  • Country: gr
    • ittsb.eu
  • job title: Industrial Maintenance Electrician
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #12 on: April 23, 2020, 10:17:04 AM »
ROUND 1 .....
Not fake lithium 18650 they sold no less than 6~8 Euro its one.

The Bosch thermal sensor it will stop the charge at 50~55C , basically this stops from charging a battery pack this left under the hot sun in the summer.
Your BMS does not look like this having it own temperature sensor, and it should have one, because this is now their protector.

One of less important issues that you will face by using original charger, this is that at charging cut off,  the charger will still deliver pulse voltage that the energy will be very low so to be used from the BMS balancing circuit (if there is one at charging mode).
Most cheap BMS they are capable at balancing due discharge.
You may add too small female banana plugs at the Bosch charger as I did too, by this way you will be able to monitor the charging voltage.

ROUND 2 ....
 
If you think going 100% Lithium?
I can pass one second advice only if your Bosch charger this using a real AC/AC transformer, does it?
WWW.ITTSB.EU   Industrial Test Tools Scoreboard  (Product Reviews Blog) / Editor in Chief.
The content of this Web site is copyright protected

Offline Gianluca

  • Jr. Member
  • **
  • Join Date: Apr 2020
  • Location: Sardegna
  • Posts: 16
  • Country: it
  • job title: Hobbyist
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #13 on: April 23, 2020, 10:43:17 AM »
My charger has this tab you see and my charger has this card you see and it is original Bosch similar to this in the photo that is not original ... I begin to think that I need to change my charger for this type of batteries .... :o

Online Kiriakos GR

  • Administrator
  • Hero Member
  • *****
  • Join Date: May 2012
  • Location: Greece
  • Posts: 2203
  • Country: gr
    • ittsb.eu
  • job title: Industrial Maintenance Electrician
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #14 on: April 23, 2020, 10:46:20 AM »
I need a picture of your very own charger internals.
WWW.ITTSB.EU   Industrial Test Tools Scoreboard  (Product Reviews Blog) / Editor in Chief.
The content of this Web site is copyright protected

Offline Gianluca

  • Jr. Member
  • **
  • Join Date: Apr 2020
  • Location: Sardegna
  • Posts: 16
  • Country: it
  • job title: Hobbyist
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #15 on: April 23, 2020, 05:42:46 PM »
Here is what is required  :)

Online Kiriakos GR

  • Administrator
  • Hero Member
  • *****
  • Join Date: May 2012
  • Location: Greece
  • Posts: 2203
  • Country: gr
    • ittsb.eu
  • job title: Industrial Maintenance Electrician
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #16 on: April 23, 2020, 06:19:08 PM »
I have good news and bad news. 

The good news ... this has a real transformer.
The bad news ... PCB this holding the metal contacts in place.

The next idea this is removing this PCB and use instead a DC/DC back converter with adjustable current (Three pots ).
Have a look here so to get some ideas. 
https://www.ittsb.eu/forum/index.php?topic=1524.0
WWW.ITTSB.EU   Industrial Test Tools Scoreboard  (Product Reviews Blog) / Editor in Chief.
The content of this Web site is copyright protected

Offline Gianluca

  • Jr. Member
  • **
  • Join Date: Apr 2020
  • Location: Sardegna
  • Posts: 16
  • Country: it
  • job title: Hobbyist
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #17 on: April 24, 2020, 07:11:06 AM »
Thanks for the info :)

Online Kiriakos GR

  • Administrator
  • Hero Member
  • *****
  • Join Date: May 2012
  • Location: Greece
  • Posts: 2203
  • Country: gr
    • ittsb.eu
  • job title: Industrial Maintenance Electrician
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #18 on: April 24, 2020, 12:46:32 PM »
Thanks for the info :)

You are welcome  :)
WWW.ITTSB.EU   Industrial Test Tools Scoreboard  (Product Reviews Blog) / Editor in Chief.
The content of this Web site is copyright protected

Offline Gianluca

  • Jr. Member
  • **
  • Join Date: Apr 2020
  • Location: Sardegna
  • Posts: 16
  • Country: it
  • job title: Hobbyist

Online Kiriakos GR

  • Administrator
  • Hero Member
  • *****
  • Join Date: May 2012
  • Location: Greece
  • Posts: 2203
  • Country: gr
    • ittsb.eu
  • job title: Industrial Maintenance Electrician
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #20 on: April 25, 2020, 04:02:58 PM »
Yes they are what you need,  but try to negotiate the price by getting five of them. 
This seller is very expensive.
True retail value for such resistors this is  0.10 € its one at local electronics shops. 

This Italian seller has more reasonable prices and I did order from him too, just  send a message if he has what you need.
https://www.ebay.co.uk/usr/computechfg?_trksid=p2047675.l2559
WWW.ITTSB.EU   Industrial Test Tools Scoreboard  (Product Reviews Blog) / Editor in Chief.
The content of this Web site is copyright protected

Offline Gianluca

  • Jr. Member
  • **
  • Join Date: Apr 2020
  • Location: Sardegna
  • Posts: 16
  • Country: it
  • job title: Hobbyist
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #21 on: April 26, 2020, 07:50:54 AM »
Hello,
thanks for the valuable suggestion ..
An ignorant question that I am but with so much curiosity ...
Waiting to be able to change my charger, I tried to charge the battery without this resistance and I saw that the battery is still recharged  :o...
Now mine was just a small test (done unconsciously) .. I don't understand the usefulness of this resistance if it is connected only to the negative pole of the battery and to the Key tag
Thanks

Offline Gianluca

  • Jr. Member
  • **
  • Join Date: Apr 2020
  • Location: Sardegna
  • Posts: 16
  • Country: it
  • job title: Hobbyist
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #22 on: April 26, 2020, 07:56:29 AM »
Yes they are what you need,  but try to negotiate the price by getting five of them. 
This seller is very expensive.
True retail value for such resistors this is  0.10 € its one at local electronics shops. 

This Italian seller has more reasonable prices and I did order from him too, just  send a message if he has what you need.
https://www.ebay.co.uk/usr/computechfg?_trksid=p2047675.l2559

have I found these even if smaller ones can be fine anyway?
https://www.ebay.it/itm/25-RESISTENZE-1-69-Kohm-1-8-watt-1-strato-met-25-pezzi/230493224642
Thanks

Online Kiriakos GR

  • Administrator
  • Hero Member
  • *****
  • Join Date: May 2012
  • Location: Greece
  • Posts: 2203
  • Country: gr
    • ittsb.eu
  • job title: Industrial Maintenance Electrician
Re: BOSCH Ni-Cd 12V How should the battery terminals be connected?
« Reply #23 on: April 26, 2020, 10:35:18 AM »
I don't understand the usefulness of this resistance if it is connected only to the negative pole of the battery and to the Key tag
Thanks

BOSCH was having a wide range of chargers, slow charge speed, medium charge speed and FAST charge in just 30 minutes.
I do not know which specific model of charger this requiring such a additional confirmation due the Key tag (resistance value) so to start charging, I can only speculate that Fast Charger model this will require it at 100%.

Because non Genuine BOSCH battery this will explode under 30Min Fast charge.   
BOSCH  genuine battery packs was using Panasonic NiCD them able to be charged with 1.7V per cell.
Chinese NiCD they follow 1.5V max charging guideline, these at 1.7V they will run hot or even explode. 
 
WWW.ITTSB.EU   Industrial Test Tools Scoreboard  (Product Reviews Blog) / Editor in Chief.
The content of this Web site is copyright protected

 

ITTSB.EU Blog

General Data Protection Regulation GDPR ITTSB.EU Home Page Reward us by a Donation - Sponsorship TsDMMViewer Data Logger for FLUKE 884xA

ITTSB Blog - Sponsors

protosnet.com - Internet solutions FLUKE benchtop DMM Repair Services

Recommended Links

Hellenic Accreditation System E.SY.D. Portal of city Volos - Greece Clean Up and Customize Facebook Firefox Backup Tool 32bit / 64 bit Winaero Tweaker = Win7 Fonts size fix